Metre
Doors, furniture & rooms

How to measure a door opening with an iPhone

By the Metre team · Updated · 3 min read

What you need

  • An iPhone or iPad with iOS 17 or later (LiDAR not needed), or a tape measure
  • Light in the doorway; open the door fully
  • A pen to write down three widths and one height

Step by step

  1. Measure inside the frame, not the wall opening

    Put the start of the tape (or your first AR point) on the inside face of one jamb and the end on the inside face of the other. Trim, plaster and door stops make the wall opening wider than the space you can actually use.

  2. Take the width at three heights

    Measure near the floor, at hip height and near the top. Old houses are rarely square, and the smallest of the three is the width that counts.

  3. Measure the height to the underside of the frame

    Measure from the floor (or the top of a threshold) to the underside of the top of the frame. If the door opens into the room, check that nothing hangs below the frame.

  4. Allow for the door leaf and the hinges

    A door swung open to 90° leaves a strip of door and hinge in the opening. If the leaf can be lifted off its hinges, measure again with it removed and note both numbers.

  5. Compare with the item and keep a margin

    The two smallest dimensions of the item have to fit inside the opening. Keep at least 2 to 3 cm (about 1 in) spare for your hands and for the walls.

Typical door sizes (for a sense of scale)

Interior doors usually have a leaf about 60 to 90 cm (24 to 36 in) wide and 198 to 203 cm (78 to 80 in) tall, but older buildings and custom doors vary a lot. Always measure yours.

Also check the way in

A doorway is only one pinch point. Measure the narrowest hall, any tight turn, the stairs and the lift as well, and compare the item against the smallest of them.

Do it with Metre

Door check Pro

  1. Open Door check and sweep the phone over the floor until dots appear.
  2. Tap + on the floor against the inside of the left jamb, then against the inside of the right jamb.
  3. Raise the ring to the top of the opening and tap +.
  4. Tap Will it pass through?, type the furniture size and read the answer. If it only passes tilted, Metre shows the angle.

Plain white door? Tap the floor, not the door. You can save your doors and check new furniture against all of them later. The Length tool measures the width and height of any doorway.

Download Metre on the App Store

iPhone and iPad, iOS 17 or later. Get Metre on the App Store.

How accurate is this?

A camera measurement of a doorway is an estimate. Metre shows a margin of error (± cm or in) and a quality label next to the result. If the item fits by less than your margin, or by less than 2 to 3 cm (1 in), measure again with a physical tape before you order or carry anything.

Measurements made with a phone are estimates. Before you cut, order or build, confirm critical dimensions with a physical tape.

Questions people ask

Do I measure the door or the frame?

Measure the clear opening inside the frame with the door open. The door leaf, hinges and stops reduce the space an object can use, so the frame opening alone can be too generous.

How wide does a door need to be for furniture?

There is no single number. The item has to pass with its two smallest dimensions, either upright or turned on its end, and you need a little spare room. Measure the item and the doorway rather than relying on a typical width.

Can I measure a door with an iPhone that has no LiDAR?

Yes. Door check works on any iPhone or iPad with iOS 17 or later. A LiDAR scanner, on Pro models, finds surfaces faster and usually more reliably.

Does Door check need Metre Pro?

Yes. Metre needs Metre Pro to measure, and Door check is part of it. The monthly plan starts with a 3-day free trial; a weekly plan and a one-time lifetime purchase are also available.

Related guides

All how-to guides · 50 animated demos in the app